Broadcast Devices AES-200 Installationshandbuch Seite 20
- Seite / 63
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Revision F • 3/12
HARRIS CORPORATION
2-8
2 Hardware Installation
Logic Supply. To drive this design, the Tally Com-
mon pins are jumpered to Logic Ground so that
an active low output turns on the status LEDs.
In some designs the status LEDs are commoned
together to ground. In this case, the Tally Com-
mon pins are jumpered to the +5 VDC Logic Sup-
ply pins so that an active high output turns on the
status LEDs.
Regardless of how the solid-state relays are con-
nected, they can switch up to 60 volts, AC or DC,
and carry up to 350 mA of current. Again, if the
tally outputs are driving an active peripheral de-
vice, the Tally Common and Tally output pins
should only connect to that device. There should
be no connection made to any +5 VDC Logic Sup-
ply or Logic Ground pin.
Using the Remote I/O Logic Connection
The
Remote I-O Logic
interface is enabled or
disabled in the ECC app (for usage details see the
Software and User chapters). When disabled, all
inputs and outputs are disconnected. The default
setting is enabled.
In most cases, a studio remote panel is used in
conjunction with the Profanity Delay upgrade
option to give the board operator control over the
Profanity Delay.
NOTE: To use the Profanity Delay
controls/tallies, a Profanity Delay
Upgrade Option must be installed.
9
23
22
25
24
7
1
31
17 Ramp Down Tally, Diversity
Ramp Complete Tally, Diversity
Diversity Delay Tally Common
Logic Ground
Profanity Delay Tally Common
Ramp Down Tally, Profanity
19
33
3
#
+
HDE-200 Internal Logic
16
Ramp Up Tally, Diversity
18
Ramp Up Tally, Profanity
Ramp Complete Tally, Profanity
+5 VDC Logic Supply
Profanity Delay Ramp Up (-)
Profanity Delay Ramp Down (-)
39
Profanity Delay Dump (-)
Diversity Delay Ramp Up (-)
Diversity Delay Ramp Down (-)
Profanity Delay Enable (+)
Diversity Delay Enable (+)
5
35
20 Critical Fault Tally
Ballpark Delay Tally
Other Tally Common
11
27
26
Warm Boot HDE-200 (-)
Spare
41
Ballpark Mode (-)
Other Enable (+)
# Pins 2, 4, 6, 21, 28, 29, 30, 32, 34,
36, 37, 38, 40, 42, 43, 44
+ Pins 8, 10, 12, 13, 14, 15
Notes:
Optional Profanity Delay activation kit required to use Profanity Delay Logic.
+5 VDC and Logic Ground should only be connected on isolated devices,
like remote control panels.
Each Enable pin must connect to +5 to +40 VDC to enable the logic inputs.
Logic inputs are triggered by active lows.
Output logic can switch up to 60 volts AC/DC (350 mA maximum current).
+5 VDC Logic Supply pins can supply up to 250 mA total current.
Other Controls Profanity Delay Controls Diversity Delay Controls
Profanity Delay Tallies Diversity Delay Tallies Other Tallies
Remote I-O Logic Interface Block Diagram
- Installation Manual 1
- User Guide 1
- Revision F • 3/12 2
- Contents 3
- CE Declaration of Conformity 4
- Safety Instructions 5
- Trademark Information 6
- Manual Revision History 6
- Product Overview 7
- 1.1.2 HDE-200 UPGRADES 8
- 1.2 Specifications 9
- 1.3 Warranty 10
- Additional Warranty Notes 11
- Services Warranty 11
- Software Warranty 11
- Disclaimer of Warranties 12
- Limitation on Liability 12
- Hardware 13
- 2.1.2 CONNECTION SUMMARY 14
- 2.2 Optional Upgrade Kits 15
- 2.3 HDE-200 Connections 16
- 2.3.3 AUDIO CONNECTIONS 17
- 2.3.5 S/PDIF CONNECTIONS 18
- Logic Inputs 19
- Logic Outputs 19
- Remote I-O Logic 20
- REFERENCE IN 21
- 2.3.9 NETWORK CONNECTIONS 22
- Software 23
- Preferences 24
- 3.2 Installing the ECC App 25
- User Group Properties 26
- 3.3 Starting the ECC App 27
- 3.4 Editing the HDE-200 28
- Network Settings 28
- HDE-200 Configuration Window 29
- CAUTION: Right click on the 30
- 3.5 HDE-200 Configuration 31
- 3.5.3 DELAY CONTROL MENU 32
- 3.5.3.2 Enable Blend 33
- 3.5.4 PROFANITY MENU 34
- Delay Management Section 35
- Recovery Section 35
- 3.5.5 SYSTEM MENU 36
- System Mode Settings 37
- 3.5.5.3 Other Controls 38
- Other Controls Section 38
- Audio Options Section 39
- Licensed Features 40
- 3.5.5.5 Show Signal Chain 41
- 3.5.5.6 GPS Configuration 41
- 3.5.5.7 Upgrade Device 42
- 3.5.5.8 Preferences 43
- 3.6 Supplemental Software 44
- Using the HDE-200 45
- 4.1.2 HEADPHONE VOLUME ADJUST 46
- 4.1.4 FAULT 46
- 4.2 Using the ECC App 47
- 4.2.1 AUDIO METERING 48
- 4.2.2 DIVERSITY DELAY CONTROL 49
- 4.2.3 PROFANITY DELAY CONTROL 50
- 4.2.4 STATUS INDICATORS 50
- GPS Lock Status Indications 51
- 5.1 Parts and Repair 52
- Services 52
- HDE-200 Replaceable Parts 53
- 5.2 Technical Overview 54
- 5 Service 55
- 5.2.2 FRONT PANEL DISPLAY 56
- 5.3 HDE-200 Troubleshooting 57
- 5.3.1 HDE-200 DEVICES DO NOT 58
- SHOW UP IN THE ECC APP 58
- TO UNBLOCK THE ECC APP 58
- 5.4 Embedded Software & 59
- Firmware Updates 59
- 5.5 Replacing Assemblies 61
- Exporter Control Center 62
- Application Note AN10-02 63
Whirlpool AKT 326/IX manuals
Owner’s manuals and user’s guides for Mixer/food processor accessories Whirlpool AKT 326/IX.
We providing 2 pdf manuals Whirlpool AKT 326/IX for download free by document types: Instruction for Use
Kommentare zu diesen Handbüchern